Repair 7

Replacing the air conditioning filter, also known as a cabin air filter, in your 2002 Honda Accord is a little involved but only requires a single screwdriver to complete the repair. A replacement filter for the Accord is available from the dealer; however, aftermarket filters are also available from auto parts stores, which may be a little cheaper if you are working on a budget.

Instructions

1

Sit in the passengers seat of your Accord with the door open. Locate and remove the two locking tabs on either side of the glove compartment then remove the three mounting screws inside the box with a Phillips head screwdriver.

2

Pull the access panel below the glove compartment loose and remove the two screws below the glove compartment with the screwdriver. Pull the glove compartment out of the dash and set it aside.

3

Remove the screws from the ends of the metal bar with the screwdriver then remove the bar from the dash. Set it aside and locate the white filter behind it. Pull up the access door in front of the filter then pull the filter out of the housing. Discard the old filter.

4

Slide a new filter into the housing, slide the access door over the filter then position the metal bar onto the dash over the filter housing. Install the retaining screws and tighten them with the screwdriver.

5

Push the glove compartment assembly back into the dash and install the retaining screws under the box as well as the three screws on the inside of the box. Use the screwdriver to tighten all the screws until they are snug.

6

Depress the two locking tabs into place, one on either side of the glove compartment, then snap the lower access panel onto the dash. Close the glove compartment.

The fuel pump on a motor vehicle pumps the gasoline through the engine to be ignited and create power. The fuel must pass through a fuel filter to ensure that no contaminants reach the engine. The filter traps large particles of dust and debris, stopping them from affecting the engine.

Start Difficulties

The first sign of a malfunctioning fuel pump filter is difficulty starting the car. The filter will start to block the flow of gasoline into the engine. This is mainly caused by blockage or clogging, but can also occur from a break in the filter or a misinstallation. The problem will escalate over time if untreated, and what began as a difficult start that took several attempts will become a complete inability to start the engine. Once the filter hits this point of damage the only fix is to replace it.

Stalling

A significant indicator of a faulty fuel pump filter is the stalling of the engine during use. The stall will most likely occur on an upward or downward slope (depending on the placement in the car) when the fuel is being pushed through the filter rapidly. The stall happens because of an interrupted or inconstant flow of gasoline and feels much like the car does when running out of gasoline. At this point, however, the fuel pump filter may just need a quick repair or cleaning.

Acceleration

The fuel pump filters earliest indicator of problems manifests as stunted acceleration. If the car starts running sluggishly or unresponsively it will mean the fuel pump is either off alignment or in the beginning stages of a clog. There is a good chance at this point that a simple fuel injector cleaner solution may fix this problem and the vehicle will start running efficiently again.

Fuel tanks are sealed environments with measures in place to prevent debris and sediment from entering an engine. An inline fuel filter catches and cleans contaminants directly from your fuel as it enters the tank. Most manufacturers do not prescribe a set interval for changing the fuel filter, but a good rule of thumb is to change the fuel filter whenever you perform any maintenance on the fuel lines or every 25,000 to 50,000 miles. The process takes around 15 minutes to complete properly.

Instructions

1

Relieve the pressure on the gas lines. Most fuel-injected vehicles have a vehicle-specific process for relieving pressure on the fuel lines. You typically release a valve near the air cleaner or use a specialized tool to force the fuel back into the gas tank. Proceed to Step 2 if you are unsure of your vehicles specific process.

2

Place hose clamps on the line before and after a joint in the fuel line. Disconnect the joint and angle both ends of the flexible line into the opening on a gas can. Release the clamps and allow the pressure to subside in the line. Reconnect the joint.

3

Disconnect the push fittings on the fuel lines connecting to the fuel filter. The connections will vary by vehicle, but most use a push connect tab that you remove before pulling the line off of the filter. Some use a garter spring that is held in place with a spring lock coupling. Open the coupling and pull the two connections apart.

4

Unbolt the fuel filter if it is hard-mounted to the frame. Install the new fuel filter by reversing the removal process.

5

Pressurize the lines. Turn the key to on, and slowly press the gas pedal to the floor three times. Wait a few seconds, and start the vehicle. Monitor the new fuel filter for leaks. Turn off the engine and correct any fittings that were not connected properly with the installation should you notice a leak.

The fuel delivery system is a vital part of your vehicles operation. Within this system, the fuel filter is a component that allows your vehicle to run smoothly. Fuel filters remove any particles from the fuel, such as dirt or rust, that may cause damage to the fuel injector, carburetor or engine. There are a few simple things that you can check if you suspect that your fuel filter is bad and needs replacement.

Instructions

1

Turn the engine off before trying to determine if the fuel filter is bad on your vehicle. You may have to work beneath the car, so allow plenty of space in a safe area for working.

2

Locate the fuel filter. Read the vehicles owners manual to determine if the fuel filter is under the hood or underneath the car. Some fuel filters are connected to the fuel delivery system, whereas some are along the the fuel line beneath the vehicle.

3

Inspect the area around the fuel filter for any obvious damage or problems. If no damage is seen, remove the fuel filter from the fueling system. In most cases, a wrench or similar tool is needed to loosen the bolts that secure the filter. If the filter is underneath the car, you may need additional tools to release the fuel filter.

4

Look at the filter closely. Note that it has a hole on both sides. Remove anything that may obstruct fuel from passing through the holes.

5

Blow through the filter. If the air passes through easily, the filter is still good. If there is a lot of resistance or you have difficulty blowing through it, the filter may be old and clogged and may need to be replaced.

6

Replace the fuel filter and tighten the bolts that secure it in the fueling system. Call a professional mechanic if you are still unsure about the quality or effectiveness of your fuel filter.